CERAKOTE PRICING

Please note, any item that arrives needing basic cleaning will be charged an additional $15.00 (the Cerakote application process cannot begin until the item has been cleaned to a basic level).

If item is not disabled and we need to to do it there will be a Disabled and re-assembled fee of $65.00

 

Return shipping will be actual cost.

 

If you spend $100 or more, we will do a free microslick on one bolt or pistol barrel.

 

We cut our own stencils in-house, and do not charge an additional fee for the stencil. The cost of stenciling is a flat fee only for stencils that require extensive labor.

Camo Patterns with more than three colors incur additional charges. Contact us for details.

CERAKOTE PROCESS

We have had quite a few questions on how the Cerakote application process is actually done.
Our first initial meeting will be to determine your colors and design.

 

After our first meeting, the following is a brief explanation of how we go about Cerakoting your firearm.

  1. Your firearm is received in our shop and examined to make sure it is in safe working order. Once it is determined that it is indeed in safe working order then it is taken to step 2, If it is not in safe working order it is returned to the customer to have it properly repaired by a gunsmith before we can take on the job. We do have access to a couple licensed gunsmiths if you want us to have the gun repaired for you.

  2. In step 2 the firearm is completely disassembled ( every last pin, nut, screw, and spring ) If the weapon has a barrel that is attached to the weapon it must be removed as well. If the barrel is not removed and the customer requests that the barrel not be removed they must sign a waiver stating so as we are not responsible for the adhesiveness of the Cerakote to that part of the weapon. We then examine each part and make notes of any problems that we see that may need to be addressed before the firearm is coated, we then contact the customer to those problems that we see so they can decide how to continue. If all parts are in good working and safe order then we continue on to step 3. Please note that some parts for example the front sights on some firearms will need to be replaced because from the factory they are either not reusable, or so extremely tight that they can be easily broken, chipped, or damaged. We will take great care in disassembly of your firearm, but things do happen from time to time that are beyond our control.
    WE ARE NOT RESPONSIBLE FOR DAMAGE TO A SIGHT DURING REMOVAL.

  3. All parts that will be coated are then given an acetone bath to remove all oil, grease and dirt.

  4. Cerakote is applied extremely light in order to not make problems with tight tolerances, That said I typically mask off pins and only shoot the heads of the pins. If you want the full pin coated you need to verify this at the time of drop off and you need to realize that you may or may not have a problem installing the pins. You may have to take some steel wool and gun lube to the outside area of the pin in order to make it fit correctly in those tight tolerance instances. We can also at request plug any holes you may wish to have plugged. Also if there are any places on the gun that you know for a fact that there will be a tolerance problem you need to let us know beforehand so we can either mask this area off or arrange for just a dusting of the coating on that area.

  5. Markings: As for markings anything that is painted or lightly laser etched will be lost during the cleaning and coating process. There is no way to save these markings. I have been asked about replacing these markings via Cerakote. We can do this but it will have more charges. Just call and ask for pricing. 

  6. Serial numbers will be masked at no additional charge when necessary. When not necessary we will coat over them as long as they can be plainly read through the coating.

  7. We then sand blast all parts to be coated with Cerakote with a very fine aluminum oxide media to remove all coatings from all pieces and to give the Cerakote a clean surface to adhere to.

  8. Each part is then taken to the coating prep area to be hung for coating. Once all parts are hung properly they are then examined once more before coating is applied to make sure all the parts are cleaned and prepped correctly and ready for a successful coating of Cerakote to be applied.

  9. The parts rack is wheeled into the Coating booth immediately after proper prep is completed to minimize the time for contamination to occur between hanging and coating. Each part is sprayed via Cerakote’s rigorous standards using equipment and technique specified by Cerakote.

  10. After the Cerakote coating is applied the parts are taken to our baking oven to bake out to Cerakote Standards. If there is any stenciling to be done the parts that require the stencil will be flashed out as required, removed from the oven stencils applied and the correct color applied, then replaced into the oven for the final bake out.

  11. After the parts are baked out they are removed from the oven and cooled. The parts are then inspected for proper coating thickness, look, and feel. If the parts are labeled as good they are taken to our reassembly area where the firearm is then reassembled for the return to the customer. If any of the parts is determined not to pass our quality standards they are taken back to step 3 to start the process all over again.

 

Note: It is recommended that the firearm not be used for approximately 3 days following coating in order to allow the Cerakote to fully harden.

If you have any questions concerning the Cerakote Application process please feel free to give us a call or drop us an email to discuss. If we don’t know the answer we know the correct people to talk to at Cerakote to find the answer for you. You can find all of our contact information here.

 

PAYMENT

 

We will email you for payment once the work is complete. We accept most credit cards.

 
SHIPPING

 

Return shipping will be included in the charges for exact shipping charges. We will apply insurance, tracking, and signature required with your return shipping.

 
TURNAROUND TIMES

 

We try to return items within a two to three-week time frame. Orders are worked on in the order they are received.

Request a  quote

TYPE

TYPE

MICROSLICK

CLEAR COAT

ELITE

Store Hours:

Monday: Closed

Tuesday- Friday: 10:00 am - 5:30 pm

Saturday: 10:00 am - 2:00 pm

Sunday: Closed

Privacy Policy | Terms of Use

© 2020 DPW GUNSMITH LLC. All Rights Reserved.

Holiday Hours:

  • New Years Eve - CLOSED

  • New Years Day - CLOSED

  • Easter - CLOSED

  • Memorial Day - CLOSED

  • 4th of July - CLOSED

  • Labor Day - CLOSED

  • Thanksgiving - CLOSED

  • Christmas Eve - CLOSED

  • Christmas Day - CLOSED

DPW GUNSMITH LLC. accepts Credit Cards. We offer a cash discount on firearms.